Grizzly Riders Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 28 Results
  1. Grizzly Engine & Transmission
    I just got this atv and I had to replace a rocker arm so I bought a new head for it. When I try to start it it made a humming noise so I turned the engine back a little ways then try to start it and it tryed to start but stoped in the same spot so can anyone help with what is wrong with it.
  2. Kodiak/Big Bear/Bruin/Wolverine Discussion
    I was given a this atv because it would not start and I’m stuck right now and don’t know where to go. When I turn on the ignition I get dash lights. Ill cycle the shifter I get neutral light, reverse light and park light. I get head lights but I get nothing from the electric start no noise or...
  3. New Member Introductions
    My grizzly has no spark stator checks in specs.had to replace pulsar coil it is in specs..replaced ignition coil still no spark which only left cdi box. Replaced cdi box still no spark please help
  4. Grizzly Talk
    Working on a 2000 Grizzly 600 ATV in my shop that was here for a carb service. After performing the service, the ATV starts right up and runs great. However, After about a minute or 2, the oil temp light goes red and the starter engages on its own. Turn the ATV off and then every time the key is...
  5. Kodiak/Big Bear/Bruin/Wolverine Discussion
    So I bought this kodiak and the rear diff bearings and seals are all shot. I got the rebuild kit and wheel bearing kit and went to work. I'm stumped on one seal. It's in the housing and there's a sleeve holding it in. Anybody dealt with this that can tell me how to get the sleeve out? There's...
  6. Grizzly Electrical & Lighting
    Seems like a fairly common fault on the Grizzly's. Just like Wessel, Have no spark. Have manual and followed Ignition Troubleshooting: Checked out following: Spark Plug ( new) Ignition Coil (checked OK) Stator, Pickup and Source Coils (checked OK) Engine Kill Switch and Main Switch (checked...
  7. Kodiak/Big Bear/Bruin/Wolverine Discussion
    Hey guys I'm looking for some assistance here. My grandfather passed away recently and has left me a 2000 yamaha big bear 400 4x4. It has not run in at least 3 years. The battery is completely shot and I was not able to pull start it. I removed the fuel line from the carburetor and it was...
  8. Grizzly Talk
    hey guys ,, i just bought a 2000 600 grizzly , green from a elderly gentleman who of used to to hunt ,, he bought it new , showed me the bill of sale and everything!!,, im so stoked cause this thing is like brand new, but i have a few questions on how the bike behaves, it has 639 miles on it...
  9. Kodiak/Big Bear/Bruin/Wolverine Discussion
    Ok so wiring is my krypton. I have a 2000 Kodiak I bought about 3 weeks ago. Everythung worked great on it now the electric start stopped working. Pulls find but kids cant pull it over. Ive checked the ground strap(looks good) and good connections. New relay last night. Still nothing. When you...
  10. Grizzly Talk
    I'm trouble shooting an issue my daughters Grizzly is having. Key on, Engine switched to run, choke on, in Neutral, battery fully charged. I press the start button, oil light glows while I am holding the start button but nothing else happens. No clicking from relay, no cranking over. Nothing. So...
  11. Grizzly Talk
    Got this grizz 04 umder 2000 miles from a guy who traded a truck for it. He said he just got it and knew nothing about them. Son ran down road about 50 or so turned aroumd not a puff of smoke all features 4x4 diff lock lights etc. work wonderful. $3800. load it up. Son takes it to ride with...
  12. Kodiak/Big Bear/Bruin/Wolverine Discussion
    Hey all, I am having a problem with my 2000 kodiak. While driving in high gear the reverse light cut on and it still remained driving forward. The only problem was it would not go over the speed it goes in reverse. I have searched for answers and think it may be the neutral safety switch but am...
  13. General Discussion
    So the fun begins The 2000 2x4 I picked up runs but will not go forwarded or back before I start ripping things apart I thougth maybe someone has had this happen and can point me in the right direction I here some noise but no movement at all its an automatic but you put in gear not sure how...
  14. Grizzly Tech Tips
    I am new to this unit and live in northern MN. I have noticed that the ATV is a hard starter when the temps dip below say 40 degrees. In fact it did not start this morning (11 degrees). I may have flooded it. The battery ran down so I have a charger on the battery now. What is the normal...
  15. Kodiak/Big Bear/Bruin/Wolverine Discussion
    Hello all, Been scouring your site for a while. Got a lot of good info to check, but ultimately still no luck. I have a 2000 Kodiak 400 4x4 I got as a parts bike. Using my 2003 for spares, I've put the bike together. The head and cylinder jug are from my 2003, otherwise engine is 2000 (in...
  16. Grizzly Snorkeling
    im trying to snorkel a early 2000's grizz 600. looks like I would have to run my spa tube right by my exhaust. so my question is will raping it in heat tape work? does it make a difference if I use the blue or white spa tube? also the air box how is every one making that work? snorkeling my 2013...
  17. Member's Rigs
    This is from the day I picked up my '05 660 in Indiana last September... My rig is a 2000 F-250 with 7.3 Powerstroke diesel. Cold air intake, 6637 filter, Bullydog PowerPup programmer, larger van turbo with Wicked Wheel impeller, Superlifts 4 and 1/2" lift, BF Goodrich 35" Radial T/A tires...
  18. New Member Introductions
    my 2000 big bear 400 fried several wires in the harness from the coil all the way to the rear end. A friend of mine told me it was risky to try and fix without replacing all electical parts. He said without knowing what caused the short we could fry it again. Just wondering what you guys...
  19. Technical Articles
    anyone looking for this i have one i would share pm me
  20. Grizzly Tech Tips
    Here are some pics of my new oil cooler for my grizzly 600, I had just put in a brand new top end and wanted to remove some of the heat, I replaced the oil cooler with a B&M 9" x 9" cooler with a Spal cooling fan, I also added a temp guage too, heres some pics really easly conversion, a little...
1-20 of 28 Results
Top