Search Results for ‘550’

Fuel sat in my quad went bad now it wont start. Drained tank, cleaned fuel injector with carb clean and added fresh gas. Added new plug. Taking long time to start. being its fuel injected should i keep trying to start it without pressing the throttle or should i have the throttle depressed while...

I need some help, I can't figure out how to open the fuse box on my 2009 550 Grizzly. It looks like it opens towards the front of the ATV but I can't figure out where and how the latch works to open it. Can someone please advise. Thanks

Having trouble with my grizzly not starting.Started for a second and now will just turn over and not try to do nothing else.Has plenty of fuel,cleaned the sprark plug and replaced air filter.

2011 Grizzly 550: After a hard rain storm or trailering the machine in wet conditions, the bike will not start until some period later when conditions have dried. This has occurred in late spring and fall (warm and cold conditions). The battery is good! Starter is good. No harness issues that I...

Hi all. I am looking at a 2013 grizzly 550 with 70 hours, 170 miles in perfect condition. With a plow and winch. Ask price is $5k. Is this a fair price? Sent from my SM-G950U using Tapatalk

Hello, I am trying to help my uncle get his 2009 Grizzly 550 running. I searched the forum and have done everything I have found on here with no luck. So now I think we are down to it being either the fuel pump or the ECM. It will turn over and fire for a second or 2 and then quit. Over and...

I have a 2009 grizzly 550 and I got some nosie coming from my rear diff I jacked it up and I spun the tire forward and it made a little bit of noise but when I spun the tire in backwards it bind up any help that may cause this I will appreciate it

Ok having starter issues. push button sometimes starts fine other times it acts like a bad battery. Very slow to turn over and sometimes just doesn't turn over at all. Put in new battery new starter new solenoid. Would a one way bearing cause this? zenchal26 is online now

first actual hard 4 wheeling trip yesterday, im coming from a 420 honda straight axle with kenda bearclaws, i have a almost brand new 2014 grizzly 550 with stock tires, i had the suspension cranked up to 5...then 3...my,question and thoughts on this machine is it feels WAY more tippy than the...

Just bought a used 2011 Grizzly 550 EPS 4WD. Previous owner installed a HMF Penland Pro series exhaust on it and the HMF optimizer. It is way too loud for me - I'm trying to do yard work and not annoy the neighbors or make my family deaf. It already has the "Quiet Core" baffle installed and it...

Trying to find general info on dping a 4 or so inch lift on my grizzly 550. And if there are any other necessary mods such as clutch kits ect brand snd websites woukd be appreciated Sent from my SAMSUNG-SM-G935A using Tapatalk

Hi all- first time here- of course 10 inches of snow and atv with plow dead- battery has 12.6 at terminals, also at starter relay, no power to instrum panel, swapped start relay out and checked its fuses still nothing- turning keys i get blinking instrum panel occassionally- tried to jump off...

So after doing some reading here I've decided that I'm going to go with a 1.5 mm shim mod, grease less Slider weights, and a purple EFI Spring. my question is about the weights. Is 12 Grams too light? or should I only go down to the 14 Gram? Just about to place my order and wanted to check first...

So like I have a 2009 grizzly 550 special edition and I've had it about a month and I was water riding (winter time) and I noticed a rear clicking in my atv it used to be just went I turn right but now it's constant anywere from 3-8 mph you can hear it popping or aggressive click I replaced all...

My 2013 Yamaha grizz 550 is having trouble shifting into low gear. I read a forum on here about adjusting the shifter linkage. The only problem, I don't know how to remove the side panel in order to get to the shift linkage. And insight on how to get this done?? Any help would be great. Thank You

Just purchased this kit from Kolpin which comes with the most unbelievably useless installation instructions I've encountered of late. Anyone ever installed one of these that could post a couple pictures?

Shaft clucht housing Yamaha Grizzly 550 has some game! Hello there, had a clacking found on my Vario, i had a Yamaha Grizzly 550,so i disassembled the Vario from my Grizzly, but i found nothing. But the shaft where the primary Vario puts on, wiggle, I can move it to difference ways, up down...

Hello all.. A couple of questions... I have been lucky enough to have my grizzly since 2011 and not had any fights with trees... Well that came to an end, lol.. Anyway, it died the winch broke and fried the winch wires, contactor and battery. It did not hurt the frame just plastics on drivers...

so i let my friend ride my baby :banghead: and he forgot to press the brake before shifting. well he managed to force it into the neutral position from park without pushing the brake for the interlock and now it wont go into park and it super hard to get it back down that far (2 hands) so...

Hi all. This is my first post on Grizzly Riders and man I do need a little advice. So to start I've read a lot of different discussions on here in reguards to clutch mods. I have a new 2014 grizzly 550 Fi EPS wity roughly 120 miles on it. I'm currently in the process of updating the secondary...