Search Results for ‘adjustment’

I'm at my whits end with this carb, need advise. Bought a used Kodiak, went thru it - it's running rich at idle to 3/4 and lean from 3/4 to full throttle. Quad is all stock. Cleaned the gas tank, new air filter, new intake, new exhaust pipe gasket, new header pipe/muffler gasket, new spark...

Hello All, just wanted to share my experience with my '08 grizzly. Today was the first time I have ever checked my intake and exhaust valves, since I bought my machine. I currently have 3200 miles on it and both of my intake valves were tight. They were supposed to be between .09-.13mm, mine was...

My Grizzly needed an idle adjustment the speed being too high and was 'clunking' into gears. This occurred after using some old but clean fuel when fuel ran out. If I turn the plastic idle knob clockwise one or two turns, the engine coughs and stops. Turning it back to its original position and...

Does anyone know how to correctly adjust the rear brakes on a 2008 450 Grizzly? I have found the brake assembly and done some adjusting but I think the brakes may be seized or rusted due to not being used. I also suspect they were never adjusted correctly from the dealership. I hope this is not...

I have a 08 Grizzly 450 4x4 and I need to check and/or adjust valves. I know how to get to the valves, but how do I know if I am on top dead center and what are the specs for intake and exhaust?

Hey Guys, how do I go about adjusting the slack out of my brake cables? brakes work, but there is a lot of slack or take up in lever before brakes are applied.

Simple poll. When you checked your valves, at either 200 or 2000miles, did you have to: turn them in turn them out they have never been done fine like they are I like pie

I needed to check my valve clearances so I figured I would shoot a little video of it. I was a bit of a mush mouth, and didn't film the whole procedure so I will add a write up with all the specs under the video. Hope you guys enjoy it! To begin checking/adjusting your valves, you should have...

Can you adjust the shifter? It seems to get harder and harder to shift every time I ride her. Sometimes the Reverse light or Park light won't go on even if I rock it. I wish it would shift eaiser. Thanks Jake

I have an '05 660 Grizzly with 1770 miles. I get some squeaking from front wheel during slow speed turn. When I pulled front wheels, both brake pads are in contact with disc. Right wheel can barely be turned by hand. Left wheel difficult to turn, but better. When brake lever pulled both...

Part 1 Part 2 Please Subscribe!! Now does this count for the wrench junkie badge?

Over the weekend I adjusted my valves on my 660. They were Ticken when i started and now my intake valves are set a .13mm and exhaust are at .17mm. Now they are Ticken like crazy!! They are set where they belong and we even looked at the book and we had it on TDC when we did it to. What is...

Well i wanted to share that I adjusted my valves on my 350 today for the first time. I know alot of you are like "so" but I have never done anything like this and I just wanted to let other members know that by looking at it on youtube and hearing what is all involved in doing it, it sounds like...

If I turn the shock adjustment to stiffer will that increase my ride height?

i have a 04 660 limited grizz. where is the idle screw? i need to adjust it and havent bought a service manual yet. thanks for any replies.

First thing first "hi to all of u grizzly enthusiast" The question i have is my grizzly is backfiring some, it runs great but just alittle back fire, i no it could be a valve adjustment, but it seems to be alittle rich, the guy i bought it from i think pulled the carb and cleaned it out and i...

i have a 09 550 with around 600mi on it how important is it to get the valves checked quad runs fine just wondering if i should get it done or not thanks for the help

Valve adjustment Hell Grizzly Riders, I’m a little less than 3 hours away from the 20 hour service on my 09 Grizzly 700 EPS. I was wondering if anyone here has ever done their own Valve adjustment. Also does anyone have a Maintenance book with the Valve specifications? Or is it a job I should...

I am going to tackle adjusting the valves on my '03 Grizzly 660, as a possible fix for the sputter/backfire through carb/cold start issues that I have been experiencing for quite a while. It is overdue for the adjustment anyway, & who knows, I might just get lucky & solve my other issues during...