carb

I have a 97 Kodiak that I have tried 2 Zoom Zoom carbs, junk. Has anyone have any better luck with another company? How about GPA MOTORS? Looks like that carb comes with a few jets but not the 105 main jet needed.

Hello all - I have purchased a new carb for this 1999 yamaha grizzly 4x4 and am hoping someone can tell me the easiest way to get to the carb, and any gotchas! i have decent mechanical aptitude but first time doing this! Thank you for looking!

I pulled a BSR33 off my 07 Grizzly 350, and replaced with a brand new one. I believe this is the correct carb for 07-14 Grizzly models. Before it was removed from the ATV I could get it to run with choke wide open, but fuel was leaking from left side of the carb out of a drain line that dumps...

Hi guys, I am rebuilding a carb for a friend for his 2000 Grizley 600. As I was re-installing the carb, I moved the starter set and the assembly separated and the spring jumped into oblivion. I have searched high and low for several hours and cannot find the spring. Does anyone have any...

Hey everyone, im new to this website and just joined because ive been having some issues with my 07 Grizzly 660. So about a year ago I purchased my quad and since I got it ive installed a triangle atv snorkel kit, and a hmf performance slip on exhaust. So ive noticed since I installed the...

I have a grizzly 660 with a BBK and aftermarket exhaust. I put in a larger jet kit as well and on flat ground it runs great and sounds great. When I put it on a hill and give it throttle it starts to spit and a little black smoke comes out. Any help would be appreciated!!!

Hello all, Just bought my first 4x4 quad. 2006 Grizzly 400. Ive been riding and fixing 450s sport quads for years and finally decided to get a 4x4. I was looking over my new purchase and noticed gas was leaking the petcock on the tank. Well I fixed that issue then realized the choke was NOT...

Dear Forum, Can anyone advise what the fixed air jet on the right side of the Mikuni N224.103 carb does?

Gents, My 660 just started idling poorly so I decided to pull the carb off and put a new carb kit in. I cleaned the carb, set the float level to 13-14mm and installed the kit. Initially I inadvertently installed the Pilot jet in the main jet and vise-versa. When the Grizzly started it backfired...

Hi All, I just bought a 2004 Grizzly 660 from a guy who had it setup to ride in the mountains. He had the stock carb re jetted to a bigger jet to handle the altitude better. I am in flat Oklahoma and it runs fine but seems to idle a little high. Since I am new to ATV's I am not really...

Brand new to site. Where can I find the order for installing a new pilot jet on a 2003 660 Griz? Does washer and O ring go in first or do I have that backwards. Repair manual doesn't show me order. Sorry if this is wrong place to post. Thx J

Here's what happened and what I've done so far. Went for a ride, at about 1 hour into it I put it in neutral and the quad started revving so high I couldn't get it in gear. Used my choke to idle it down to get it in gear. Then the idle went back to normal but I couldn't go past a quarter...

I'm having idle and running issues with the machine I just bought. Was apparently sitting for a while and the gas was a year old. It ran fine for a little bit but when I opened it up she started bogging down around 20 mph. I'm pretty sure it just needs a good carb cleaning but seafoam hasn't...

Hey I hav a 660 yamaha grizzly.. just cleaned the carb and put it back together.. now it starts and idles fine and will accelerate up to about 14km/h before it starts bogging and sputtering and dies.. what could my problem be?

I own a 02 stock 660 with a mikuna bsr42/1 carb. Atv has low mileage and no abused. Developed a problem with mid range sputtering and no power/stalling while climbing hills. Took carb apart and cleaned with carb cleaner. Checked diaphram and appears no cracks or damage. Removed float needle...

hey my Grizzly 660 idles high when its warm it happened after i cleaned it the reason i cleaned it is because it died on me on a trail i had to be pulled back to the truck. this is what i have done so far i cleaned the carb very good 3 times poking jets to clean them out really good and see...

How do you clean the carb on a 2007 Grizzly 450. Machine has sat for 2 years.

Sorry - if I"m in the wrong topic, let me know! _________________________________________ I woke the Griz up from winter slumber and the 5 yr old battery was dead. Not unexpected! A new battery and I fired it up. It wasn't easy, but it never is with this one, especially when it's cold. I got...

Alright I dont know a lot about re-jetting a carb, or if I even need to. I bought an 03 model 660 Grizzly for $200 that needed the top end of the engine rebuilt. I ordered a 686 bore kit off of Ebay, and I've been running it for a year with no problems at all. But I just feel like I'm missing...

Hey guys, long time lurker new poster.. I need some help trouble shooting my Griz.. Here is the problem I have been having: (A little long but this is a complete occurrence to current problem) About a month ago I was crossing some water, while doing so, it sucked in some moisture and began...