Grizzly Riders Forum banner
crank

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-12 of 12 Results
  1. Grizzly Tech Tips
    Hello, I have searched the forums but could not find anything that matches my issue, I have a 2005 660 with a no start seems to lock up when the spark plug is in and cranks over fine when it's out, we have replaced the starter, battery ,carb and relay, and had the valves adjusted, and can not...
  2. Grizzly Engine & Transmission
    Has anyone done it. And do I have to machine the block Sent from my LG-D850 using Tapatalk
  3. Grizzly Talk
    Hi im new to the forum im in need of help i recently swamped my bike... I took all the precautions ( did not crank it, changed oil several times, changed sparkplugs) and it still will not crank i am going to change the oil again but i need to run the bike a for a lil while before changing it...
  4. Grizzly Electrical & Lighting
    2011 Yamaha Grizzly 700 4 wheel drive I recently changed timing chain and can't get it to start tested the starter; and after I did that when I want to go to turn it on nothing happens lights on the pod come on but the fuel does engage when I press the ignition button nothing I've checked all...
  5. Grizzly Engine & Transmission
    I got a 2005 grizzly 660 The crank case keeps filling up with gas. I stripped it down today and noticed the fuel cock doesn't shut off. Also the engine is locked up? It was running just fine. shut it off and about 10 min. later I noticed gas pouring out of the air box? is it just a bad NEEDLE...
  6. Grizzly Engine & Transmission
    Replacing bearings in crank case due to dirty pond water. Pulled all bearings and all are open type except one yamaha part# 93306-20464-00 which goes on the end of the axle drive shaft. This bearing has a rubber seal that is in the blind side of the crankcase. Has anyone else seen this and why...
  7. Technical Articles
    Anybody know how to get the left side crank bearing off the crank?
  8. Official Clutch Forum
    Guys, I,am fixing to install the 1.5 mm shims in my clutch and I have it all clear in my mind but one thing. after installing everything back together when its time to torque the 22mm crank nut back on. I believe it torques to 90 ft lb. how do you fellas hold the crank from turnning when doing...
  9. Grizzly Engine & Transmission
    OK, '09 Grizzly 550 ran rough for a while, I replaced the spark plug cap, it was burned on the inside, at the contact. Like it made a bad contact and was arcing. After installing a new cap it seemed OK, my 15 year old son rode it for a while. When he got home he said it still ran rough some of...
  10. Grizzly Electrical & Lighting
    I have a 2006 Grizzly 660 and have starting issues. I put a timing light on the spark plug wire to check if I have spark during crank. There is no spark until I crank for about 30 seconds, then it is intermittent for another 10 seconds then it will finally start. Up till today, once I got it...
  11. General Discussion
    Hey over the last few weeks my 660 was cranking slow and we thought it is the batt well now the batt quit so I put a good batt in and the selinoid buzzes like hel* what does this mean???? TIA!!
  12. Grizzly Dyno/Tuning
    I will put this here instead of fs section if you want to move it its ok but if anybody had a used 550 crank they wanted to sell or let me use it would be great it can be damaged as well I want to send one in to see how out of balance it will be with a 105.5 piston on it. Its the one thing i...
1-12 of 12 Results
Top