Search Results for ‘drive’

Hi guys and gals. I've been having an issue when I'm sitting on the throttle at low or high speeds (doesnt seem to matter which as long as it's at a steady speed) where the machine will drop out of drive and the red "R" signaling reverse will light up on the dash only for a split second before...

After someone crashed my 2000 Yamaha kodiak 400 altramatic into a tree (front tire hit and bent rim, wheel bearings destroyed but frame took no damage) my front drive shaft began moving in and out while turning the back wheels forward but not in reverse. Does anyone know why this is happening?

Does anyone know? To be specific what is the direction for the bruin/grizzly 350? But I would think all the shaft drive models would turn the same.

Good afternoon gents! I've been tasked with doing some repair work to my father in laws 08 grizzly and have a few weeks before deer season to finish it up. I'm have one HECK of a time finding any repair information on the net for this thing. The biggest problem is the rear drive shaft, the...

How do I get to the seal ? Do I need to disconnect the u joint first? Any help and info would be appreciated!

Recently had to change the rear diff in my 09 450. I know what phasing the drive shaft is but...when taking apart the shaft I noticed that the spline can only be put together one way due to an extra wide row of teeth on the male portion that corresponds to an extra wide groove one the female...

Hey guys just want some pointers. I have my front end apart to replace my drive shaft due to well known fail issue with drive shaft. I am second owner of this 04 660 grizzly. As planed, when I moved my front diff forward the shaft fell out of coupler on motor side. But I cannot seem to get...

Need help... novice mechanic ... greying man trying to add ATV owner / repairer to his bucket list. Bought 98 Grizzly 600 which had been sitting in snow for 6 months. Needed new brakes, wheel bearings. When I removed the rear axle, there was oily crud in the bottom of both tubes so I decided...

I need to change the front driveshaft in my 2006 660 grizzly and I was wondering what all I would have to take off to do this job and how it comes out? Thanks for any help.

I have a 1998 griz 600 4x4. it was a basket case when i got it. down to needing a flywheel and starter drive. the pull rope is a bear. Any help or info on interchange would help.

As you guys know the 660's are having trouble with the front drive shafts going bad... well mine went bad and I do not have the time to fix it so can I remove the front drive shaft and still be able to drive it? Does it seal anything on the engine side or the front diff for keeping oil from...

Greetings from the new guy....... After an awesome ride today I noticed that my rear drive shaft was just slightly wet where it goes into rear diif. Well not really wet but just enough to make a little dust stick to it, no drips or anything like that. I think it will probably be a problem...

New to this site by virtue of purchasing an 07 Grizzly 350 4x4. I hope someone can help. I purchased this Grizzly for $500.00, not too bad of shape with the exception of one issue. When the machine is in neutral, it will roll for about a foot and the back wheels lock up.....like it was placed...

Hey guys, just brought the griz in after a nice ride. I was spraying it off when I noticed some grease (assuming it diff fluid) around my front drive shaft on the end that connects to the front diff. I'm not sure how long it has been like that. There haven't been any puddles of fluid on my...

I need to replace the front drive shaft on my 2004 Grizzly 660 model #YFM660FLES. I bought a aftermarket one of of Amazon and it is like 1/4 inch to short. I don't understand why it is off. Anyone have any problem like this before? Anyone know of one that fits exactly right or where I could fins...

Hi, on my 2006 Grizz i noticed that where the front drive shaft goes into the engine, there is a lot of play and the splines are showing. i am asuming that the flange coupler that is attached to the motor is worn out. my question is how do you go about removing the coupler? and would it be a...

a couple of years ago we was out playing and my grizzly started making a weird noise, come to find out the front drive shaft had came out of the front of the engine didnt do any damage to the causing , but what had happened was thec boot closest to motor came apart and then the u joint messed up...

I have a 2012 7oo Grizzly and after running Ill hit my kill switch to let the fan run . While sitting there with the kill switch off and key on the 4 wheel drive will engage and disengage by its self. The dealer has never heard of anything like it. It seems to be the kill switch that causes it...

I was wondering if anyone has had this problem. I've been noticing lately when I start my Grizzly up that ever so often my 4 wheel drive indicator light would be on. It would usually stay on for a little bit even though I hadn't used it previously. Tonight I unloaded it from the trailer and...

Hello, I have a 2012 grizzly 700 with power steering and am having a problem with the 4 wheel drive. The 4 wheel drive keeps coming on and off, like your pushing the red 4x4 button in and out non-stop, but the button is not being pushed? I can hear the 4 wheel drive motor engaging and...