Search Results for ‘end’

Ok Im trying to rebuild a Big Bear rear end. Ive got all the parts for the swing arm pivot. Now Im stuck trying to find the bearing that is pressed on the axle. Is there a seal and bearing for that side? Also whats the best kit to rebuild the rear diff?

Damn, it took 30 years of driving to cause my first accident, and on Friday the damn 13th. Did a low speed rear end into the back of a lifted truck and got into it's trailer receiver. The only place it made contact with was at the very front center of the hood close to where it...

Congratulations to all of you who've survived the holiday season (relatively) unscathed-you deserve a reward, and some of the web's biggest moto gear retailers have got you covered. Both Revzilla and Cycle Gear (among others) have been discounting some of your favorite motorcycle gear as we...

So I'm looking at upgrading my 2011 Grizz 700 to 14" SS212 wheels and 29" or 27" Dirt Commander tires. I know I will lose bottom end and am looking at 1.5 shim with a purple spring. Will this be enough to bring back the quad to usable power levels with a HMF performance exhaust and fuel...

I have a 1987 Big Bear 350 that I am fixing up for bush use. After having it sit around for a month, I decided to move it to work on it and I noticed that it makes a grinding noise at higher speeds (or in high-range). However the noise isn't constant, only occurring at "x" amount of tire...

Hi Folks, been searching the internet and maybe you can help me. I have a 2002 kodiak 400, with MANY MANY miles on her (spedometer broke long ago) Its begun making a clicking noise in 4wd, going straight or turning. In doesn't happen in 2wd. Where do I begin to look? Ive done lots of...

Got to rebuild my top end on my grizzly 700 and could use a lot of help its smoking pretty bad think it's just rings anyone know of a manual

Having to rebuild the top end on my 2009 Grizz 450 due to my wife thinking it was a submarine... Blue Smoke and the whole 9 yards. Got the valves cleaned up and everything measured within specs and put a soda blaster to it but the jug had to be re-bored to +2. The shop ordered a Namura 11:1...

I looked through several threads on grizzly 700 / raptor 700 top end parts, but i have not found out what im looking for. Any help is appreciated! Ok i bought a grizzly last night, the timing chain is stretched pretty bad, and the cam needs to be replaced. I was leaning on the raptor 700...

I have a 2006 Wolverine 450 4x4 And i have to change out a ball joint. So first question has anyone done this before? From looking at it ..i was thinking of just pulling the lower a arm and than change it out. Also i have a little bit of play in the bars..and steering stem. Last year i replaced...

I recently rebuilt this bike, it was smoking . I re did the cylinder new valves springs and timing chain and new piston . Now it has a noise it didn't have beforehand . I've adjusted the valve lash to spec to no avail. I've searched high and low for answers . Please help

Hey guys i have a 06 griz 660 and the top end is bad on it (smoking bad uses oil wont move in reverse) and i was wondering if any of you guys have recommendations on what or what not i should do to the motor Thanks !

Hello every one I'm new to the form. Just working on my 2002 kodiak and the front diff went, i got a use diff. in off a 2005 unit with both axels. but notice my steering knuckles are damaged. Though I might change rest of front end to newer model. has any one done this. Axels and spine count...

I have some issues with the front end on my 03' 660 grizzly. Can I remove the the front drive line axle and still drive the machine. The axle is shot, just not sure if by removing the axle if that will allow debris to enter in?

I am not q complete idiot but I may have second guess that after I tell yall this ... Bought a 2000 griz 600 the piston skrit blew up and sent a bunch o metal into the bottom. So I bought itreal cheap I took everything apart than I made my first mistake broke a motor mount off the l case got a...

Edited Video of a group ride we did last weekend.

Hi everyone. I just obtained a new to me Yamaha grizzly 600. It was my uncles. He got rid of it because someone ran it without oil and now it knocks. Long story short, I need some bottom end advice. I want to go ahead and pull the engine and replace main bearings and possibly upgrade piston and...

ok fellas I need help again. heres what i,ve got, new 700 grizz, 27" black diamond tires and 1.5 sim mod (wish I did the 2mm mod). all else is bone stock. its still real boggy from the start and if i,am off road i definatly need low range and it still leaves allot be desired. nothing like when...

Ok picked up a 07 grizzly 450 for cheap after the pervious owner had a top end job done one it and it was still smoking and started knocking afterwards. Tore top end down and found piston to be extremely lose in jug. Put a caliper on everything and found piston measured 3.303 and jug to be 3.343...

Hey guys, I have a 09 700 grizzly that I am getting annoyed with. Everything on the quad is stock except my tires. Currently I have 26x10-12 and 26x12-12 swamp lites, so nothing crazy. Where I ride in Newfoundland marsh areas the ground is extremely spongy and always wet but you can drive...