Grizzly Riders Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 73 Results
  1. Grizzly Tech Tips
    Well looks like the cold weather got my battery in my 2011,700 grizz can somebody tell me the biggest cca battery that will fit my bike and best place to buy it please. Thanks bob in tn
  2. Grizzly Engine & Transmission
    2002 Grizzly 660. Water in oil. Drained it all, very nasty - almost like tan paint. Flushed it a few times.... still nasty Never been in any water over 6" so it was not from sinking it or running in water too deep. I started looking at everything on the cooling system since it was apparent the...
  3. Grizzly Chassis & Body
    Hi guys, Overhauling the rear diff on my 03 Griz and I'm having trouble beating the pinion bearing out of the housing. I'm using an "All Balls" kit from Royal. I beat the hell out of the pinion and it came out, but I'm having an issue with the bearing. I assume the gear on the diff side of...
  4. General Discussion
    Does anyone know the HP on the new 708s?
  5. Grizzly Tech Tips
    I was given a 600 yamaha griz that had not run for three years. I asked owner if it had run good when he parked it, he didn't know. This vec has 4500 miles on it. first thing I noticed the carb was blown off the engine and rubber manifold was ruined. Well I cleaned things up gas tank and carb...
  6. New Member Introductions
    Bike slow to accelerate and makes an awful noise. However after a few seconds the bike responds to the throttle
  7. Grizzly Engine & Transmission
    Is there a kit to convert a 2011 grizz 700 to dual oil filters ? if so who makes it please ? thanks bob
  8. Grizzly Engine & Transmission
    Need help... novice mechanic ... greying man trying to add ATV owner / repairer to his bucket list. Bought 98 Grizzly 600 which had been sitting in snow for 6 months. Needed new brakes, wheel bearings. When I removed the rear axle, there was oily crud in the bottom of both tubes so I decided...
  9. General Discussion
    Hi there 2000 griz 600 1800$ owner clams no fire would you buy it???
  10. Custom Accessories
    I could not find a hitch that even came close to my requirement so I made one. It attaches at four points to the frame and is also attached at the original hitch for a fifth point. It is super strong and is back far enough to not interfere with the rear rack when towing. It also provides support...
  11. Grizzly Engine & Transmission
    our poor griz gets used a lot for pulling a trail mower and gets pretty warm, was wondering if anyone had experience with installing a bigger cooler and where would be a good place to get one.:smiley_confused1:
  12. Member's Rigs
    Hello from N Virginia...here is my griz with a few mods so far...just did the 20 hour service at 180 miles....Skids, winch, overfenders, rims/pitbulls, JBS sheave, rigid SR2-10" and lots of fun
  13. General Discussion
    5 members are celebrating their birthday on 01-01-2014: -Mitch (Age: hidden or unknown) -Arizona Griz (Age: hidden or unknown) -Toxarch (Age: hidden or unknown) -mudduck (Age: hidden or unknown) -ruthless (born in 1974, Age: 40) Happy Birthday!
  14. Official Clutch Forum
    I'm looking for suggestions for a few clutch mods for my 2013 700. I've done a little research and it looks like the "kits" are overpriced and I should piece together my own "kit." I'm currently running 14" ITP rims with 27" zillas and I ride both mud and trails. I have no other mods besides...
  15. Grizzly Engine & Transmission
    Hey guys, long time lurker new poster.. I need some help trouble shooting my Griz.. Here is the problem I have been having: (A little long but this is a complete occurrence to current problem) About a month ago I was crossing some water, while doing so, it sucked in some moisture and began...
  16. Grizzly Electrical & Lighting
    I need to Fix the wiring as i managed to tear it apart in the woods where does the "plug" end of the unit reside? just wondering if i'll be in for a quick job or if it heads way back mixed in to the main harness to the cdi or something. I still have enough to solder but will have to remove it...
  17. Grizzly Engine & Transmission
    This thing seems to run great when trail riding for an 30 minutes to an hour, then begins idling very fast. The first time it happened I couldnt even put it in gear. Then I remembered that I could start it in gear so I turned off the engine and put it in gear then restarted it. After riding this...
  18. Grizzly Talk
    Hey Folks, I Picked up my Griz yesterday, after the 15 hours drive there and back. I got my first ride today. I did little bit on the stock tires, they are fine for riding on hard pack trails, but they definitely would not be any good for the off main trail riding. With a hole 3 KM on the Girz...
  19. Official Clutch Forum
    I have been reading this site and others for a few days now. Lots of good information but would like to hear opinions on my set up and opinions before I begin/order. I'm looking for that low end grunt and dont want to loose my top end speed either. I plan on going with UTV inc. 660 machined...
  20. Grizzly Tech Tips
    hey rebuiling 2000 griz 600 so I torqued down the first 2 nuts on the jug which were the long ones went to torque the other which are just regular looking nuts cant get torque wrench in so i tried a crows foot and couldnt get enough grip on nut (scared to round it at this point haha) any ideas...
1-20 of 73 Results
Top