Search Results for ‘grizz’

New to the forum i have an 07 grizz 450, just asking what you guys think the best brand wheel bearings to put in it

2011 Yamaha Grizzly 700 4WD Yammy Blue 194 miles/27.9 hours and garage kept Warn XT25 winch with synthetic rope Has never seen mud, I rode it in the mountains of Utah on just a few trips, some scratches on fenders Newer Duracell AGM battery that sits on a trickle charger Comes with arched truck...

2002 grizz 660 11.1 high comp hotcams stage 2 raptor springs k&n clamp on snorkels ra Hey guys the wheeler sat for a couple years got it home cleaned the carb changed the oil ran great for about 3 miles easy riding. Started to act like it was running out of fuel then a couple little back fires...

Got my hands on a 350 and possible 660

Hi all I'm struggling with hmf optimizer settings. Bike: 2017 grizzly 700 SE Mods: hmf qs slip on silencer, k&n airfilter, hmf optimizer, 27in zillas Milage: 560 ****Does anyone have same setup that could give me settings for 2017? Issues: 1. At times when I let off gas, the trans brake...

Hi All I recently purchased a 2009 Grizzly with 7500km on it. It was well maintained and doesn't appear top have been beaten. It does however have one concerning "CLUNK". When the engine is at idle and in any gear including neutral. If press the throttle there is an audible clunk right as the...

just want someone to verify my conclusions and i would appreciate any recommendations for parts. just bought my atv, is a 2008 grizz 450 4x4. guy i bought it from just installed a new battery, looked clean and not abused. i rode it around for 30 minutes or so and nothing seemed odd and...

Hey everyone I'm a new user and made up my mind to buy a used Grizz as my first ATV. I've looked for the past few weeks and narrowed it down to two quads: 2012 700 w/ EPS - 1400 Miles, Good Shape with Winch. Second owner, 75 hours. $5750 2014 550 w/ EPS - 500 miles, Excellent Shape and...

I'm going to check the valve clearance on my 2011 Grizz 700 for the first time and I'm also wanting to check the timing, but I'm not sure how to do it. What tool (light gun?) do I need for this job and how is it done?

I'm wanting to run Shell Rotella T6 synthetic in the 700 Griz but I can only find it in either 0W-40 or 5W-40 weights, and the manual says it's ok to use everything BUT those weights...5W-30, 10W-30, 10W-40, 15W-40, 20W-40 and 20W-50. Would it be ok to use the Rotella 5W-40 or do I need to...

08 grizz 700 has 158 hours and 500 miles on it. i recently replaced wet clutched regreased primary clutch and installed a new one way bearing. when in neutral i rev up the grizz and on the decel it makes a loud clunk. the clunk doesnt happen everytime as its intermitten. any ideas???

Hey guys, just joined and after a long time of riding, I finally got my own Grizzly. Only catch is, in order to not end up paying child support (lol) I actually got a 2006 660 for free. It's a fixer upper, ready for mud, snorkeled, and I started tearing it down last night. It actually runs, but...

New to grizz, and 4 wheelin. Traded my street bike for a 12' Honda foreman. Decided to get another bike and came across an 02' grizz 660. The grizz is completely original with 420 miles and 150hrs. Still has original tires and a-arm protectors. None of the factory recalls have been done to...

Hey im new to the club just curious about how many miles people are getting out of there grizzlies, I have an 09 with 9300mi, and it's still a beast

So I did this awhile back , and thought I would share. I put a extra battery into my rear cargo area , I ran one Hot wire to my positive on my front battery , and hooked it to the rear positive. I placed fuses at BOTH ends in case of a short. For the negative , I ran a ground wire (blue in...

hey guys hope ya can help , I seem to be having problem with the shifter on my 2000 grizzly 600 is there an adjustment to the cable that comes from the foot brake? it seems like when the bike is cold I cannot move that damn shifter , but if I stomp on the brake pedal it seems to free up. once...

Hi Da Grizz, welcome to the forum! Why not make this your first post and introduce yourself to us?

Just unboxed the SW and I'm trying to figure out where some of these parts will be installed. For the most part everything seems straight forward but I'm having trouble deciding where these should go... Piece on the right is the solenoid (and is maybe called a 'contactor' in some of the...

Here's what happened and what I've done so far. Went for a ride, at about 1 hour into it I put it in neutral and the quad started revving so high I couldn't get it in gear. Used my choke to idle it down to get it in gear. Then the idle went back to normal but I couldn't go past a quarter...

Hi Grizz monster 88, welcome to the forum! Why not make this your first post and introduce yourself to us?