Search Results for ‘install’

Hello all - I have purchased a new carb for this 1999 yamaha grizzly 4x4 and am hoping someone can tell me the easiest way to get to the carb, and any gotchas! i have decent mechanical aptitude but first time doing this! Thank you for looking!

Hello all! Newbie here, I’m starting a rebuild here soon and I would love the feedback and advice. I haven’t dove this deep into a motor in a good bit. So back track a couple years I bought this lovely machine for $900 not running. Got it running a couple times, not more than a couple minutes...

hi i can get a complete eps from a 2008 grizzly ,guy will give me complete wiring harness off quad too ,will it fit my 2009 or is frame or some brackets diffferant

Putting in a SW Terra 35 and I've decided the crimp I'm looking at here isn't something I can reproduce so I need to figure out who to take this wire to get the end put back on after I get it shortened to where I need it. Never having delt with wires this big I have no idea who I could go to...

im trying to get my choke needle assembly back into carg on my 450 but it won't slide in correctly the spring is so tight I can't get the plastic nut to thread on, even if I could the choke cables push out the back, so I figure the needle is not sliding in, any help on how to get this back...

I have the rear diff. out and drive shaft and am looking at the universal yoke and bearing housing. Do I unbolt the several nuts that hold the housing to get to the oil seal or do I have to unbolt the universal yoke first?

Hey guys. Install is going good just wanting to know if anyone has any stories of them using the remote to operate the winch? I can understand its for the cable snapping but I have synthetic rope. I'm new to the winch game so any help to this n00b is great!

Figured since i havent posted in a while, would post up some pics of the Rigid lights ive installed on the grizz. How i installed the 10" SR lightbar on my Yamaha HD bumper Heres how i installed the D2s on my bars. Used a piece of flatstock and some u bolts. Worked pretty well.

I've got a 2011 Grizzly 450 and i'm installing a winch. i'm not sure were to tie in the " keyed power on" wire. Any recommendations?

Hello, I just finished relocating my rad to the front rack using a kit from Wild Boar ATV. While I was doing this I figured I'd buy a new Rad and Fan kit as mine were looking rather worn. So I've installed everything and got 'er running again but the fan is doing some funky things. It seems to...

I found a way to replace the servo motor only on the newer 700's. Some of you may remember my older post about replacing them in the 02-08 660's. While I can still can get those motors as well. I finally got the newer servo motors back from the machine shop. The newer ones fit the following...

Hi Guys! I just bot some gauges and need some info on where to put the sensors. Both the oil pressure and water temp gauges say to install them into the block. Does the 07 700 have frost plugs or "spare" plugs that I could use?? If not, where should I hook the oil pressure gauge too?? The...

I have a new 700 Grizzly that I put 29.5 outlaws on. The bike lost a lil ummp after installing the tires but not a whole lot. I wanted to get the low end back and done my research. After reading the clutch kit Exposed thread on our forum here i went to ordering parts. I ordered 4 450 weights...

Sooooo.... I put the High Lifter radiator kit on my 700 today and got it all put back together. I cut the factory plug for the factory fan off and wired the two wires off the HL fan to the two stock wires that used to go into the plug. Now when I turn the key on, the fan instantly turns on...

Here are some pictures of my new radiator install. During the last SSRT ride a rock must have kicked up and punctured the radiator so a new one was a must. I searched around and the only upgrade radiator available I could find was one off eBay. I was hesitant since it wasn't from a known...

does anyone know where to buy a snorkel kit and where to find a DETAILED video or pics on installing them.i have a 02 grizzly 660. thanks or maybe a backwoods remedy to make a set.

Sold to Chasmack

Guys- I read through a bunch of posts and did not find what I needed. In the directions it says to remove bottom tie bolt. What is this?? Where is this?

How do I remove the plug from inside the left handlebar? I trimmed off the end of the rubber grip to install a new mirror and discovered a steel plug that prevents me from inserting the mirror mount. Is the plug pressed in and permanent? 2012 550 Thanks, cliff