Grizzly Riders Forum banner
kit
1-20 of 131 Results
Advanced
  1. General Discussion
    wondering if anybody would be interested in buying a jbs 450 grizzly/Kodiak sheave.comes with sheave,blue secondary spring,12 and 14 gram od weights(some wear).to buy new they are 415 USD with only one set of weights.will sell for 275 USD.i am located in Canada but willing to ship to the U.S...
  2. Parts For Sale
    I have a HMF performance series pipe for sale and hmf optimizer I had them on my grizzly for about a month I have a new n2d snorkle kit NIB never installed would like to sell all of this make an offer I just want it out of my garage call or text 7127390049 snorkels are black not red like picture
  3. Grizzly Electrical & Lighting
    hi, new here. think im in the right forum now! ha im looking for ideas about where to put my 2nd battery!? i dont have a cargo box. is there room somewhere besides the two storage compartments? im leaning towards the front compartment where the gas tank was on earlier models.has anyone done...
  4. New Member Introductions
    hi all,new here. im getting a daul battey kit for my 2016 grizz 700. i dont have a cargo box, and besides the two storage compartments is there room for it some where else?? im leaning towards the front compartment,where the gas tank was located on earlier models! has anyone done this? or have...
  5. Grizzly Engine & Transmission
    I was thinking of 719 cc big bore kit . Is it good for long use and is it reiable. And can we run it at stock cams and valve springs . I read that you must change the valves into raptor 660 valves ? And do you have to change the cams Sent from my SM-G900FD using Tapatalk
  6. Official Clutch Forum
    So I am looking at buying new tires and am thinking Kenda bear law htr's in 27"x12 tire size. My 2013 Grizzly 700 EPS is totally stock otherwise and I'm wondering if I wait to put a clutch kit in until spring or summer if riding that way could do any damage to the motor or transmission? We...
  7. Grizzly Tech Tips
    im trying to get my choke needle assembly back into carg on my 450 but it won't slide in correctly the spring is so tight I can't get the plastic nut to thread on, even if I could the choke cables push out the back, so I figure the needle is not sliding in, any help on how to get this back...
  8. Grizzly Accessories
    For a limited time we are putting our Grizzly 700/550, 450, and 660 kits on sale! $165.00. That'll get you bars, risers, a dash plate, and a bar pad. Take advantage while you can. Thanks! ATV Handlebar / Bar Riser Combo Kits ? Rox Speed FX
  9. Parts For Sale
    Well I sold my Grizzly, and the new owner wasn't interested in the snorkel kit, so I need to sell it. Its a Grizzly Full Flow Snorkel kit made by a guy in Canada out of his own shop. He make's hundreds of these kits, and are commonly known throughout the world of Yamaha Grizzlies. The kits new...
  10. Kodiak/Big Bear/Bruin/Wolverine Discussion
    Hey all...I was wondering if anyone has used or knows anything about the machined aluminum block lift kits...good or bad? I think Quadrax and Kimpex make them.Machined aluminum blocks for each shock mounts on the ATV. Lifts 1” to 1-1/2” depending on the vehicle. Suspension travel remains...
  11. Grizzly Chassis & Body
    Ok...so I just put on MSA Kore 14" rims and Mega Mayhem 27" tires. Tonight I put on a Highlifter 2" lift kit and after looking at the angle of the axles, it has me a little worried. Here are a couple pics. Do these seem angled too much and should I remove the lift? Thanks.....
  12. Grizzly Snorkeling
    Grizzly 350 SRA Snorkel - YouTube So after alot of research I finally snorkeled my 350 , it wasn't to hard to do and it turned out pretty good. I am going to upload a video and some pics. If you have any questions or need help with snorkeling a 350 let me know I...
  13. New Member Introductions
    I need help on how to put together a clutch kit for 2013 grizzly 700 with electric power steering! I'm gonna put 29.5 swamplites on it and probably get some 29.5 terminators later. What kind of effect will the clutch kit have on the bike if I put the stock tires back on it just to goof around?
  14. Official Clutch Forum
    I put 14 inch wheels and 28 swamp lites on my grizzly and need a clutch kit. looking for one that wont break the bank and wont kill my top end so much. I do all around riding trails. hill climbs and mud.
  15. Grizzly Talk
    I was wondering if anyone could tell me who makes a 2 inch lift kit for my 2014 grizzly 700 ?
  16. Official Clutch Forum
    Hello, first post here. I have a 2009 grizzly 700 efi with 27" mudcat tires. The primary reason for purchase was to plow my driveway with a 60" moose blade. I also use it for yard work and dragging heavy crap around. keeping that in mind I want to get the clutch kit that will work the best for...
  17. Parts For Sale
    FOR SALE: Grizzly 700 Full Flow Snorkel Kit. Kit was installed on bike and lightly ridden around yard. Basically a brand new kit. Comes with everything except a small bar of "JB Weld Kwick plastic" that is used, optionally, in the install to relocate the tip over sensor out of the way. Also...
  18. Official Clutch Forum
    okay so I just ordered silver back 30 9x14 tires to put on all four corners an I was recommended to get the extreme clutch kit is that a good kit to turn those tires an will it give me more grunt
  19. The Official "MUD" Section
    Would this work on a grizzly? My friend picked one up for his 07 kq 700 but he ended up selling his quad before he ever used it (surprise sale he wasn't expecting someone to have that much interest in it). He sell it to me if I can make work for dirt cheap. Just wondering if it would? Thanks...
  20. Official Clutch Forum
    have a 07 grizzly 700 with 28x10x12 and i put a team clutch kit and it did not do any thing for my griz and was wanting to know if any one has any ideas to what i can do to get more torque out of it. it is a fully clutch kit wet and weights ty any help would be great
1-20 of 131 Results
Top