Grizzly Riders Forum banner
popping
1-13 of 13 Results
  1. Kodiak/Big Bear/Bruin/Wolverine Discussion
    After someone crashed my 2000 Yamaha kodiak 400 altramatic into a tree (front tire hit and bent rim, wheel bearings destroyed but frame took no damage) my front drive shaft began moving in and out while turning the back wheels forward but not in reverse. Does anyone know why this is happening?
  2. Grizzly Chassis & Body
    New member here, my first post (besides introduction). So here is the story, I bought a new 2018 Yamaha grizzly 700 eps, rode it gently around the yard for the first 18hrs then did the break in oil change and filter, then we took it to Nevada and rode it a hundred miles or so, mostly trail...
  3. Grizzly Tech Tips
    I need some help my right rear axle keeps popping out on my 660 grizzly. It's a gorilla axle I have tryed bending out the stock clips that didn't work. I upgraded the clips to the gorilla sqaure clips that didn't work. I have the rear support brace added. I always fill my diff untill it...
  4. Grizzly Engine & Transmission
    My left side axle shaft keeps popping out , I've changed fluid , circlip, cleaned and re packed c.v ..splines are good , bearings are good , ball joint is good, .. Any ideas. The bike is a 2005 660 with 800 Kms and completely stock. I just bought it and have only gone for one ride . I'm beyond...
  5. Kodiak/Big Bear/Bruin/Wolverine Discussion
    I just bought a 2006 450 Kodiak and it runs great when giving it throttle but when letting off the throttle it takes a second or two for it to idle down and it also pops too on decel. I pulled the carb thinking that maybe the throttle plate may be sticky and not completely shutting instantly...
  6. Grizzly Engine & Transmission
    I think I just need to buy a new carb. We have rebuilt the top end of 600, new piston, had the valves ground. We ran the valves 3 times after, just to make sure they were right. We rebuilt the carb twice, both times putting the parts in a cleaning bin. The motor won't idle, won't respond to carb...
  7. Grizzly Dyno/Tuning
    Hello guys i have a problem, my 660 grizzly was idling kinda high and it was causing the atv to lurch forward whenever i put it in gear, so i was told to lower the idle screw, it cleared the problem right up, now though, i get a popping, sputtering, on deceleration. If i set the idle back up to...
  8. Grizzly Engine & Transmission
    howdy guys, new user here with a hopefully easy question. I have a 2002 Grizzly 660 ultramatic, recently had the carb cleaned and the mech said i needed it rejetted. Charged me 370 bucks for a rejet and carb cleaning and machine wouldnt start cold here in Michigan. Made a small adjustment to the...
  9. Grizzly Engine & Transmission
    Hello all We replaced a front outer cv joint boot on our 06 660 Grizzly and now the axle keeps popping out of the diff(about an inch or so). We replaced the circle clip on the axle hoping that was the problem, but still happening.We can take weight off front end and slide axle back in, but then...
  10. Grizzly Talk
    Hello all was wondering if anyone could help with my question. I have a 2011 Grizzly 550 4x4 and did a little trail riding Saturday nothing much but noticed when I was done my inside back CV boot was torn and there was a popping noise coming from it. I immediately put it on the trailer and...
  11. Grizzly Tech Tips
    OK, so I FINALLY got my EHS Bullet box installed, and took it for a spin. It was OK, but not the thrill ride I had hoped for... anyway while I was out test riding on my backyard track, I had a noise coming from under the left front. It was popping with the speed of the bike, so I figured it was...
  12. Grizzly Tech Tips
    Hey y'all, I'm new to this forum, so bear with me. I've got an '09 Grizzly 550 with about 30 hours on it. I'm running 26" Mud Lites, with no other mods. I've got a couple of issues I need help with. 1) My front brake goes all the way in, unless I "pump" it, then it will grab. I'm thinking...
  13. Grizzly Engine & Transmission
    I have a 07 450 Griz 4x4 that makes a popping sound in the rear when turning. It sounds like it is at the wheels on both sides. I checked the play in the CV joints and they seem good. I greased the housing at the wheel and the rear drive shaft but it is still making the noise. Im a total noob so...
1-13 of 13 Results
Top