Grizzly Riders Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 160 Results
  1. New Member Introductions
    Fuel sat in my quad went bad now it wont start. Drained tank, cleaned fuel injector with carb clean and added fresh gas. Added new plug. Taking long time to start. being its fuel injected should i keep trying to start it without pressing the throttle or should i have the throttle depressed while...
  2. Grizzly Talk
    I just purchased a new to me 2014 Grizzly 700 to use primarily as a workhorse around our land. After going over all the fluids, etc. I noticed I'm missing a few of the plastic rivets that look and act like screws for the fenders. I've found the Yamaha part number and was going to order a few...
  3. Grizzly Tech Tips
    When I remove the battery terminals it dies and it won't charge the battery. Don't really know much about these machines
  4. Grizzly Chassis & Body
    I have a 2011 550 grizzly with a warn front mount plow system.My question is, does anyone make a front bumper-brush guard that will bolt in place with the warn front mount plow bracket in place.I like the looks of the moose one, but it looks like it bolts to the same holes as the plow mount bracket.
  5. Kodiak/Big Bear/Bruin/Wolverine Discussion
    I am in the process of rebuilding the entire rear end (bearings and seals) on my Big Bear. Ordered the parts from a Yamaha dealer close by for the middle gear seals and o-ring. Can someone tell me what the correct part number is for the front facing lower seal which drives forward transaxle? I...
  6. Grizzly Tech Tips
    I loaded my Grizz into the back of my F150 this weekend for some fun. After about a half hour ride there and back, I found this bolt in the bed of my truck after unloading the ATV. I cannot figure out where it came from. It is a unique fastener- so I thought I would take a chance and see if any...
  7. Grizzly Engine & Transmission
    Hi, recently brought a used 2009 Grizzly 350. During oil change, I had up on a jack to check over. The front right tire was harder to turn than the left, which was easy. So I took hub Assm. Off checked the wheel bearing, not those. Very good shape. Removed the axle, and that bearing right behind...
  8. Grizzly Accessories
    I just got a 07 Griz 450. I want to get a snow plow for it and reading on this excellent site about what you guys use. I saw a you tube video where a guy bought a plow only to discover it wouldn't work with the specific model# of Warn winch he has so he had to buy a new winch. I don't want...
  9. Grizzly Talk
    Hey everyone, I haven't posted in a while which means everything is going great with the machine, except.. Today before our ride I was doing my normal inspection to make sure nothing looks wrong. I was checking on the front axles when i noticed the front left side was a bit weird. I have...
  10. Grizzly Electrical & Lighting
    im almost positive mine is bad at this point, replaced stator rectifier coil and checked every wire to try and regain spark. now i dont know why they are so rediciously priced on ebay, but i did find some cheaper ones for i think it was a 350 warrior for like 40.00 and the plugs are the same...
  11. General Discussion
    I have a 03 660 ive been working on from time to time, its got 29.5 Outlaw 2s all the way around...shes got 3 axles popping so shes been parked for a few months...im getting ready to put in 4 new Sixity axles and wheel bearings, but im kinda wanting to do a little clutch work to it while its...
  12. General Discussion
    Hello, ever since it was new my 450 has been backfiring on decleration.it only pops once.i found that touching the throttle a little bit while declerating stops this.i guess this means it's running lean.i have a uni filter and am about to add a tip which will make it even leaner and a jbs kit...
  13. Grizzly Engine & Transmission
    Looking at buying an 08 700 from a friend, and getting away from Honda. The bike has a bad crank, though. What are my options as far as rebuilding the motor? Can the crank be "rebuilt", or am I going to have to buy a new one? Can someone point me in the right direction? Not exactly looking for...
  14. Grizzly Tire & Wheel Combos
    Looking to put a set of silverback on my stock 2011/12 (can't remember of the top of my head) grizzly 700, now I have a couple questions Should I be running a skinny/wide combo, I'm running this setup in Canada now I'm not entirely sure but I heard skinnys are good for water holes that had a...
  15. Grizzly Electrical & Lighting
    The reverse light on my 2002 660 blinks when I first start it. I have to shut the ignition switch off and restart quad and light goes off. I also have a sputtering problem while climbing hills. Read a few posts and wanted to know if they could be related. Have cleaned carb and changed spark...
  16. Kodiak/Big Bear/Bruin/Wolverine Discussion
    Hi all...I have a 2013 kodiak 450 eps and have 26" zillas (9" front and 11" rear)on 12" itp 212s...I have ordered a shim kit (2-1mm,1-0.5mm,and 1-0.2 shims)...any recommendations on what shim to use...from what I have read on here, I was thinking maybe 1mm...any input greatly appreciated!...thanks!
  17. Grizzly Engine & Transmission
    I have a 2013 Grizzly 450 EPS, and I have a quick question. Is it harmful to shift gears from neutral to high OR from high to neutral while the four wheeler is in motion?
  18. General Discussion
    my 450 griggly will pull start 1 pull but the electric start does not work changed out starter relay and it still doesnt start. All i get is a buzzing sound from starter relay same as with the old one put voltage meter on battery 1236 volts when i turn key on and push starter button voltage on...
  19. New Member Introductions
    How do i post a question ????
1-19 of 160 Results
Top