Grizzly Riders Forum banner
rebuild

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 36 Results
  1. Parts For Sale
    I pulled a BSR33 off my 07 Grizzly 350, and replaced with a brand new one. I believe this is the correct carb for 07-14 Grizzly models. Before it was removed from the ATV I could get it to run with choke wide open, but fuel was leaking from left side of the carb out of a drain line that dumps...
  2. Kodiak/Big Bear/Bruin/Wolverine Discussion
    Ok Im trying to rebuild a Big Bear rear end. Ive got all the parts for the swing arm pivot. Now Im stuck trying to find the bearing that is pressed on the axle. Is there a seal and bearing for that side? Also whats the best kit to rebuild the rear diff?
  3. General Discussion
    Got to rebuild my top end on my grizzly 700 and could use a lot of help its smoking pretty bad think it's just rings anyone know of a manual
  4. Grizzly Tech Tips
    Having to rebuild the top end on my 2009 Grizz 450 due to my wife thinking it was a submarine... Blue Smoke and the whole 9 yards. Got the valves cleaned up and everything measured within specs and put a soda blaster to it but the jug had to be re-bored to +2. The shop ordered a Namura 11:1...
  5. Home Page Features
    Read more about How To Rebuild your ATV Master Cylinder at ATV.com.
  6. Kodiak/Big Bear/Bruin/Wolverine Discussion
    So I bought this kodiak and the rear diff bearings and seals are all shot. I got the rebuild kit and wheel bearing kit and went to work. I'm stumped on one seal. It's in the housing and there's a sleeve holding it in. Anybody dealt with this that can tell me how to get the sleeve out? There's...
  7. Kodiak/Big Bear/Bruin/Wolverine Discussion
    Long story short the piston ate the cylinder walls. Took jug off, replaced with over sized piston and had jug machined to new piston. Got it all back together and crank timing is kicking my tail. I turn the 17mm bolt on the crank to the TDC timing mark per service manual, set cam to straight up...
  8. Grizzly Tech Tips
    Just bought an 06 Grizzly 660. It was lightly used, good condition. I've been finding a puddle of gas underneath it when i come out in the morning, gas dripping from overflow tube tucked out from foot area. I'm assuming the float is stuck and gas is flowing out. I was considering taking...
  9. Grizzly Tech Tips
    Hi, new bee to forum and 1st time Grizzly owner. Looking for informatiom and tips on rebuilding a 07 700 griz. engine due to rod bearing disintegrated. Parts recomendation,factory or aftermarket. Would like to go back stock. Thanks to all that reply.
  10. Grizzly Tech Tips
    Where does this hose go? Just finished a card rebuild kit.
  11. Grizzly Dyno/Tuning
    I have an 05 660. I was looking on ebay for a carb kit and notice that there are complete replacement carbs available for reasonable prices. Has anyone tried these carbs? Having a replacement to bolt on would minimize downtime(though this time of year it's not a big deal) and leave me with the...
  12. Grizzly Talk
    So last week I went riding at lost trails in pa for the first time. There was more rock than anything. So long story short I crashed my 450 and bent the frame and jammed my front driveshaft. So this is going to be my weekend project for a few weeks. From start till now
  13. Grizzly Engine & Transmission
    So today I ripped out the rear diff because there was some funky stuff going on while riding. I replaced the pinion main and needle bearing last week, come to find out the main berings inside were bad and now I got metal in my new bearings for the pinion. Regardless Ive got it all broke down and...
  14. Grizzly Tech Tips
    Rebuilt the carb using the Moose rebuild kit. Replaced everything except the needle and seat (the kit was a brass set, where as I had already used an upgraded stainless steel set). Original issue was that it was dumping fuel into the oil, replaced the needle and seat and it did it again awhile...
  15. Grizzly Engine & Transmission
    any info on doing a complete engine rebuild myself? like to do it myself and save money, the shop said $2000 to do it so thats alot of money.
  16. Grizzly Engine & Transmission
    well today was a bad day for my 660 grizzly, had it to the shop and got some bad news, needs a top/bottom rebuild, going to cost around $2000 to do it..crap, does that sound like a good price? like to find an engine somewhere if i could save a little cash
  17. General Discussion
    Well as some of you know when I went to trailfest i blew a headgasket on my 660. Well soon to come is a rebuild! 1 wisco piston and rings (stock size) can get a kit with all gaskets needed for a topend build for 312 bucks on ebay. 2 Possibly new exhaust valves 3 HMF S/O 4 left rear axel seal 5...
  18. Grizzly Tech Tips
    Hey, I'm new here! I just got a 2003 Grizzly and the rear differential needs new gears. I've purchased all the seals, bearings, and gear set, BUT..... What is the proceedure for shimming the big gear and the shims needed for the small pinion gear? I've tried a few combintations that make...
  19. Grizzly Tech Tips
    Hello everyone, Today I took on the task of rebuilding the top end of a 08 grizzly 350 for a friend of mine. The reason we were doing the rebuild was due to a loud tapping sound comming from the top end. |With the head off we noticed there is a decent amount of play in the cam bearings. Is...
  20. General Discussion
1-20 of 36 Results
Top