Grizzly Riders Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 28 Results
  1. Grizzly Talk
    I have a 2011 grizzly 550 bike hase low milage . A wierd whining noise comes out of starter when starting anyone know what could be the probleme ? Thanks
  2. Grizzly Talk
    Hi everyone, went out to fire up my 700 the other evening and this is what I get... Anyone have any suggestions as far as what it could be, bad starter? Battery seems to be fine, lights power on, dash works, I keep it on a tender if it ever sits too...
  3. Grizzly Talk
    I have a starter/relay issue. the grizzly wont start the normal method (ignition on, in park, kill switch off, push start button), and by bypassing to starter relay the starter starts to turn, but stops after 1 sec. I believe the starter and the relay are bad. I have been through 4 relays in 4...
  4. Grizzly Talk
    Ok having starter issues. push button sometimes starts fine other times it acts like a bad battery. Very slow to turn over and sometimes just doesn't turn over at all. Put in new battery new starter new solenoid. Would a one way bearing cause this? zenchal26 is online now
  5. New Member Introductions
    HI guys my name is mike i have a 2005 grizzly 660 hunter edition I am having an issue with my starter button not working. First of all i just got this atv and am new to grizzly's for the little time i rode i loved it plenty of power and the 4x4 is great very fun. so i got the atv of some guy...
  6. Grizzly Talk
    Working on a 2000 Grizzly 600 ATV in my shop that was here for a carb service. After performing the service, the ATV starts right up and runs great. However, After about a minute or 2, the oil temp light goes red and the starter engages on its own. Turn the ATV off and then every time the key is...
  7. Kodiak/Big Bear/Bruin/Wolverine Discussion
    Went riding with my son today and my battery ended up falling out of the mount and it pulled my starter solenoid off the frame now my quad will only start by touching the 2 bolts on top of the solenoid with a screw driver. Does anyone know how to wire these things back up so I can hook it back...
  8. Grizzly Tech Tips
    im trying to get my choke needle assembly back into carg on my 450 but it won't slide in correctly the spring is so tight I can't get the plastic nut to thread on, even if I could the choke cables push out the back, so I figure the needle is not sliding in, any help on how to get this back...
  9. Grizzly Engine & Transmission
    Hello all.. A couple of questions... I have been lucky enough to have my grizzly since 2011 and not had any fights with trees... Well that came to an end, lol.. Anyway, it died the winch broke and fried the winch wires, contactor and battery. It did not hurt the frame just plastics on drivers...
  10. General Discussion
    Can someone give me an idea where the starter motor is located on a 2011 Grizzy 350 4x4. Better yet what needs pulled off to get to it (if anything). I need to clean and check the cables to the starter motor, it appears, my sons been running it in deep water, and he finally told me he hasn't...
  11. Parts For Sale
    I have a 1998 griz 600 4x4. it was a basket case when i got it. down to needing a flywheel and starter drive. the pull rope is a bear. Any help or info on interchange would help.
  12. Grizzly Electrical & Lighting
    Hello, I have a 98 Grizzly with an electrical issue I believe. Grizz has sat in a garage for along time and after charging battery up and cranking for awhile and not starting/firing the starter now stays engauged/energized as if the start button was stuck, even If I turn the key off it still...
  13. Grizzly Tech Tips
    Hello All, I have two 04' Grizzly 660s both of which were having issues starting. So I searched for a way to Override the start button because my drive selector indicators were not working. Even after adjusting the linkage I was still having issues. So using a few simple crimps, some wire and...
  14. Grizzly Electrical & Lighting
    ive looked and i cant find nothin on this, on my 04 660 i can turn on the key and all of the display comes on, the nuetral light, speedometer every thing, then when i press the button, nothing.... no click or anything. but i can touch the two poles on the starter relay together with a screw...
  15. Grizzly Engine & Transmission
    Earlier in the summer i swapped frames on my 03' 660.(long story). Anyway prior to starting the project it started fine. Once I got it most of the way back together i went to start it up and all i get is a clicking/buzzing sound from the relay, and i can hear the starter turning. Relay is new...
  16. Grizzly Electrical & Lighting
    Guys any idea on how to stabilize this thing? Just bought a new one and it works just comes loose at the connection. I put dielectric grease on it. Super glue maybe?
  17. Grizzly Talk
    Has anyone found a way to waterproof/seal this thing? Drives me nuts replacing it when wet. Ideas?
  18. Grizzly Electrical & Lighting
    I think my starter is bad but want to make sure my diagnosis is correct. I can hear it spinning but no crank. Battery is good 13+ volts very little voltage drop when i push the start button. If I bypass the relay, same thing spins no engage> Thanks for your opinions....T
  19. Grizzly Electrical & Lighting
    anyone ever mess with the starter clutch, Basically i buried my grizz a while back ever since then its been harder and harder to start........pulling the pull start turns the starter as well (so hard to pull), now the starter just spins and wont engage the crank to spin, I am going to take it...
  20. Kodiak/Big Bear/Bruin/Wolverine Discussion
    Just picked up a BB and trying to figure out why the electric starter is not engaging, it spins just fine I even pulled it out and it seems that there isnt anything in the hole it came out of. I would think that there would be some gears in there to crank the motor. Any Ideas
1-20 of 28 Results