Search Results for ‘valve’

Doing this for the first time on the old 2011 Grizz 700 and have a few q's? I've found valve clearance specs as such... Intake 0.09-0.13 mm (0.0035-0.0051 in) Exhaust 0.16-0.20 mm (0.0063-0.0079 in) If anyone can confirm that'd be great. I've been told to adjust the valve clearances to...

i just thought i'd share that a king quad is the same one since the only way to buy on for a grizzly is to buy the whole throttle body. its $140 and a lot better than 600.. gr rules

Hello All, just wanted to share my experience with my '08 grizzly. Today was the first time I have ever checked my intake and exhaust valves, since I bought my machine. I currently have 3200 miles on it and both of my intake valves were tight. They were supposed to be between .09-.13mm, mine was...

Out of curiosity, I cut apart and inspected the OEM Denso oil filter off my Grizzly 700 after its first oil change. Pics: I was not impressed! So I set about to find a better replacement, and will have a full article coming out soon. In the meantime, I noticed the OEM...

I have looked everywhere for the answer to this question and I cannot find an answer or a picture. On my 05 660 the needle valve sits under the Float tang. Connected to the top of the needle valve is a little clip or spring that somehow Connects to the float tang. Can anyone explain how that...

Keep getting gas in the oil and fillin up the air box not too happy about it i could really use some advice... oh yea and the carbs less than a year old

I have a 08 Grizzly 450 4x4 and I need to check and/or adjust valves. I know how to get to the valves, but how do I know if I am on top dead center and what are the specs for intake and exhaust?

is there a secret to pulling the valve cover? i have taken all of the bolts out, but the cover wont budge. is there a secret bolt i am missing? i have checked my manual and got all of the bolts i found in the manual. any help will be appreciated.:thanks:

Does anyone know the proper intake and exhaust valve clearances for an 08 Grizzly 350 IRS? EPI clutch kit, dyno jet, K&N air, and ITP XTs keep it rolling. Any help is appreciated. SDC

Anyone know the valve clearance on a 2007 400 griz?

I am in the process of getting parts for my topend rebuild on my 660. My qestion is how do i remove my valve guides? And how do I install my new ones? I dont wanna mess anything up so i figured i might as well ask.

Is there a seal on every valve or just the exhaust valves??

My 660 smokes at start up then it goes away and it doesent smoke when you hammer it so does this mean valve seals? Also how much of a bitc* is it to change them? And they are only on the exhaust valves right?

Simple poll. When you checked your valves, at either 200 or 2000miles, did you have to: turn them in turn them out they have never been done fine like they are I like pie

I needed to check my valve clearances so I figured I would shoot a little video of it. I was a bit of a mush mouth, and didn't film the whole procedure so I will add a write up with all the specs under the video. Hope you guys enjoy it! To begin checking/adjusting your valves, you should have...

Part 1 Part 2 Please Subscribe!! Now does this count for the wrench junkie badge?

Over the weekend I adjusted my valves on my 660. They were Ticken when i started and now my intake valves are set a .13mm and exhaust are at .17mm. Now they are Ticken like crazy!! They are set where they belong and we even looked at the book and we had it on TDC when we did it to. What is...

Saturday i'm gonna adjust my valves on my 660. Well on the airbox lid it says what the adjustment should be for the intake valves and the exhaust valves. Well for the intake it says the adjustment should be between .10-.15 and the exhaust between .15-.20. Well my feeler gauge has...

Well i wanted to share that I adjusted my valves on my 350 today for the first time. I know alot of you are like "so" but I have never done anything like this and I just wanted to let other members know that by looking at it on youtube and hearing what is all involved in doing it, it sounds like...

My grizz started smoking, so I took the tope end apart to investigate. I found that the exhaust valve was leaking between the valve guide and valve. So I removed them. Here is my problem I cant get them back in. I have tried just about everything, I have baked the head, froze the guides, made...